Stihl MS 180: Tips to Fix Won't Stay Running Issue
Are you struggling with your STIHL MS 180 chainsaw suddenly stalling and refusing to stay running? You're not alone. This issue can be frustrating, but with the right troubleshooting, it's often fixable. Let's dive into some common reasons why your MS 180 might not be staying running and how to address them.
The STIHL MS 180 is a popular saw among homeowners and professionals alike, known for its power and durability. However, even the most reliable tools can develop issues, and a common one is a sudden loss of power or stalling. Before we begin, ensure the saw is cool to prevent any burns, and always wear safety glasses and gloves when handling the tool.
Fuel Issues
One of the most common reasons for a STIHL MS 180 not staying running is fuel-related problems. Let's explore two key sub-topics here.
Incorrect Fuel Mixture
STIHL recommends a 50:1 fuel-to-oil ratio for the MS 180. If the fuel is not properly mixed, or if you're using the wrong type of oil, it can cause the engine to stall. To fix this:
- Drain and refill the fuel tank with fresh gasoline.
- Purchase the correct 2-cycle engine oil from STIHL.
- Mix the fuel and oil in the correct ratio (50:1).
- Let the saw sit for a few minutes to allow the fuel to settle.
Fuel Contamination
Over time, fuel can break down and become contaminated, leading to engine deposits that can clog the carburetor and cause your MS 180 to stall. If you suspect fuel contamination:
- Drain all the old fuel from the tank and fuel lines.
- Clean the fuel system using a suitable fuel system cleaner.
- Refill the tank with fresh fuel mixed at the correct ratio (50:1).
Air Filter Issues
Another common culprit behind a STIHL MS 180 not staying running is a clogged or dirty air filter. Here's how you can address this problem.
Removing and Cleaning the Air Filter
The air filter should be cleaned or replaced every 50 hours of operation or annually, whichever comes first. To do this:
- Access the air filter by removing the left-hand side cover.
- Remove the air filter cover.
- Take out the air filter, and inspect it for dirt and debris.
- Clean the filter with compressed air (if it's a paper filter, replace it; if it's foam, clean it with soap and water).
- Reassemble the components and test the saw.
Regular maintenance, like keeping your STIHL MS 180's air filter clean, can help prevent a sudden loss of power or stalling. Always follow the manufacturer's guidelines for maintenance to keep your tools running smoothly and safely.
Additional Checks for a STIHL MS 180 Not Staying Running
If you've addressed the fuel and air filter issues and your MS 180 is still not staying running, there may be other underlying problems. Below are two sub-topics to consider.
Spark Plug Issues
The spark plug could be fouled, worn out, or not properly gapped, leading to engine misfires and stalling. To troubleshoot this:
- Remove the spark plug wire.
- Abstaining from touching the metal part of the spark plug, pull the spark plug out with a spark plug wrench.
- Inspect the spark plug for signs of fouling or wear.
- Clean the spark plug if necessary, or replace it if it's worn out.
- Reassemble the components and test the saw.
carburetor Adjustment
If your STIHL MS 180 is running poorly or not staying running, the carburetor may need adjusting. The carburetor controls the fuel-air mixture in the engine. To fine-tune the carburetor:
- Locate the high-speed (HS) and low-speed (LS) screws on the carburetor.
- Turn the HS screw clockwise until it's snug, then back it out one full turn and one filósoper.
- Turn the LS screw clockwise until it's snug, then back it out two and a half full turns.
- Start the saw and allow it to warm up, then fine-tune the screws as needed.
If you're unsure about any of these checks or need further assistance, don't hesitate to contact a professional mechanic or STIHL's customer support. Keeping your STIHL MS 180 in top condition will ensure it stays running and keeps your work efficient and safe.
Now that you've explored the various reasons why your STIHL MS 180 might not be staying running and how to address them, you can tackle these issues head-on. Regular maintenance and prompt troubleshooting are key to keeping your tools in working order. Happy sawing!